<R1>
1단계 - 기본설정
Router>enable
Router#configure terminal
Router(config)#no ip domain lookup
Router(config)#line console 0
Router(config-line)#exec-timeout 0 0
Router(config-line)#logging synchronous
Router(config-line)#exit
Router(config)#hostname R1
2단계 - 라우팅 테이블 설정
R1(config)#interface loopback 0
R1(config-if)#ip address 100.1.1.1 255.255.255.0
R1(config-if)#exit
R1(config)#interface serial 0/0
R1(config-if)#ip address 10.1.12.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#interface serial 0/1
R1(config-if)#ip address 10.1.13.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
3단계 - 라우팅 프로토콜 설정
R1(config)#ip route 100.1.2.0 255.255.255.0 10.1.12.2
R1(config)#ip route 100.1.3.0 255.255.255.0 10.1.13.2
R1(config)#exit
라우터 통신확인
R1#show run
R1#ping 100.1.2.0
<R2>
1단계 - 기본설정
Router>enable
Router#configure terminal
Router(config)#no ip domain lookup
Router(config)#line console 0
Router(config-line)#exec-timeout 0 0
Router(config-line)#logging synchronous
Router(config-line)#exit
Router(config)#hostname R2
2단계 - 라우팅 테이블 설정
R2(config)#interface loopback 0
R2(config-if)#ip address 100.1.2.1 255.255.255.0
R2(config-if)#exit
R2(config)#interface serial 0/0
R2(config-if)#ip address 10.1.12.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface serial 0/1
R2(config-if)#ip address 10.1.23.1 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
3단계 - 라우팅 프로토콜 설정
R2(config)#ip route 100.1.1.0 255.255.255.0 10.1.12.1
R2(config)#ip route 100.1.3.0 255.255.255.0 10.1.23.2
R2(config)#exit
R2#show run
<R3>
1단계 - 기본설정
Router>enable
Router#configure terminal
Router(config)#no ip domain lookup
Router(config)#line console 0
Router(config-line)#exec-timeout 0 0
Router(config-line)#logging synchronous
Router(config-line)#exit
Router(config)#hostname R3
2단계 - 라우팅 테이블 설정
R3(config)#interface loopback 0
R3(config-if)#ip address 100.1.3.1 255.255.255.0
R3(config-if)#exit
R3(config)#interface serial 0/0
R3(config-if)#ip address 10.1.23.2 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#inter
R3(config)#interface serial 0/1
R3(config-if)#ip address 10.1.13.2 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
3단계 - 라우팅 프로토콜 설정
R3(config)#ip route 100.1.1.0 255.255.255.0 10.1.13.1
R3(config)#ip route 100.1.2.0 255.255.255.0 10.1.23.1
R3(config)#exit
R3#ping 100.1.2.0
R3#ping 100.1.1.0
'Base > Network' 카테고리의 다른 글
9. Dynamic Routing (RIPv2) (0) | 2022.05.21 |
---|---|
8. 원격 서비스를 이용한 Router 관리(Telnet, SSH) (0) | 2022.05.21 |
6. Static Routing (0) | 2022.05.17 |
5. Router 2대 토폴로지 구성 (Packet Tracer 실습) (0) | 2022.05.16 |
4. CISCO Switch / Router (0) | 2022.05.14 |
댓글